Florida humidity and shade turn a wood deck green with algae and soft with rot faster than almost anywhere else in the country. We remove that buildup safely. Low pressure and the right cleaning solution do the work instead of a standard pressure washer, which can splinter and damage wood. For decks that need more than a clean, we also offer sanding, staining, and sealing to bring back the original look. We serve homes throughout Bradenton and Manatee County.
Removes algae, mold, and mildew that hold moisture against the wood
Uses low pressure so boards do not splinter or lift
Catches early signs of rot or loose fasteners during the visit
Brightens weathered wood and prepares the surface for staining or sealing
Reduces slip risk from algae buildup on walking surfaces
Extends the useful life of the deck
What’s Included in Our Deck Care Visit
An inspection of the deck surface, railings, and fasteners
A cleaning solution applied to break down algae, mold, and mildew
A low pressure rinse with a wide fan tip, never a narrow blast
Attention to railings and stairs, which often need more work than the flat boards
A walkthrough to point out anything found during the inspection
Cleaning a Wood Deck in Florida’s Heat and Humidity
Shaded decks and those under tree cover stay damp longer after rain, which is exactly what algae and mildew need to take hold. Manatee County’s humidity keeps that moisture around even on dry days. Wood decks here build up organic growth faster than decks in drier climates.
Left alone, that buildup does more than look bad. Trapped moisture leads to wood rot, and a deck that feels soft or spongy in spots is often further along than it looks from the surface. Regular cleaning removes the moisture source before it reaches that point.
Our Deck Cleaning and Restoration Process
We inspect the deck for rot, loose boards, and damaged fasteners before starting.
We apply a cleaning solution suited to wood, which breaks down algae and mildew at the source.
We rinse at low pressure with a wide fan tip, not a narrow blast that can splinter boards.
We clean railings, balusters, and stairs separately, since they often hold more buildup than the flat decking.
For decks that need more than a clean, we sand the surface to remove lifted fibers and old finish, then apply stain or sealer once the wood is fully dry.
Wood is one of the few surfaces where high pressure causes real damage rather than just being unnecessary. A narrow, high pressure stream can lift and splinter the wood grain permanently, and that damage does not wash out.
What Not to Use on a Wood Deck
Pool chlorine and household bleach can discolor wood and harm nearby plants and grass. A wire brush can scratch the surface and tear wood fibers, leaving the deck rougher than before instead of smoother. Standard high pressure settings, the kind used on concrete, are too strong for wood and can splinter boards on contact. A dedicated wood cleaning solution paired with low pressure removes buildup without any of these risks.
Deck Cleaning Cost in Bradenton
Cleaning alone typically costs $0.30 to $0.60 per square foot, or about $100 to $500 for a full job depending on size and condition. Adding sanding, staining, and sealing runs higher, usually $2 to $6 per square foot, or roughly $600 to $1,800 for an average deck. Railings and stairs often add more labor than the flat decking itself. Every baluster has to be cleaned individually. Every deck is different, so we do not post a flat rate online.
Real photos from actual jobs carry more weight than anything we can say about ourselves.
Before and after, algae removal in BradentonWeathered deck, before and afterDeck restoration project, Bradenton FL
Deck Care FAQs
How long does it take to pressure wash a deck?
Most decks take a few hours to clean, depending on size and how much buildup needs to come off. If sanding or staining is part of the job, the full process can take one to several days to allow proper drying between steps.
How often should decking be cleaned in Bradenton?
Most Florida decks need cleaning once or twice a year. Shaded or heavily wooded areas often need it more, since they stay damp longer and grow algae and mildew faster.
What should you look for when choosing a company for this work?
Ask what pressure setting and cleaning solution they use, since the wrong combination can damage the wood. Ask whether they check for rot or damage before starting. Ask if staining or sealing is available too, in case you want more than a clean surface.